Latest Android firmware for MXQ Pro TV Box WIFI RTL8189 Realtek

UPDATE PAGE CLICK HERE

 

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

26 Comments

  1. louiji on December 17, 2016 at 4:19 pm

    Why is my burning tool in Chinese and how do I change it to English???

  2. Richard Lawrence on December 19, 2016 at 12:46 pm

    i keep getting this error message when it reach 93% [2016-12-19 11:36:51 715][HUB2-4][0x30702004]Uboot/Temprature Testting/Get result/Out of range

    • MediaBox on January 8, 2017 at 4:29 pm

      UPDATED instructions are here: 📣https://mediaboxent.com/unbrick-mxq-pro/

    • Keko Jones on February 7, 2018 at 12:35 am

      Hi there.
      In some ocasions there are a temperature error around 97% , its very simple to fix that problem just go to and click View and in the right side of the temperature parameters ad an extra cero (0) and should be ok to go 100% complete !
      Thanks For your videos and Firmware, ” Boricuas in the House “

  3. Johnnny Jon John on December 21, 2016 at 10:22 am

    I bought an OTT MXQ Pro on amazon and received them with outdated firmware. Play store wouldn’t work and kodi was an old version. Kodi was also full of bloatware.

    After trying a few firmware updates that ranged from bad to worse, I was able to use the one listed on this page successfully. Play store works fine now and Kodi is updated to latest version so I was able to install Exodus. Kodi is also a slimmed down install which makes it run faster.

    Overall, I am very impressed with this firmware. The remote and wifi work fine on it. I would highly recommend giving it a try.

    I used the USB Burning Tool to flash the boxes.

    • Mahesh on December 26, 2016 at 8:37 am

      Hi JOhn,

      I am getting below error while trying to update the firmware via usb burning tool.
      romcode/initialize ddr/read initialize status/usb control setup error

      I have tried changing the USB cable and diff. versions of USB burning tool.

    • MediaBox on January 8, 2017 at 4:33 pm

      I update the instructions check this page. 📣https://mediaboxent.com/unbrick-mxq-pro/

  4. Bilek on December 26, 2016 at 7:21 am

    Hi need Help. When I reset the device is the device under Burning Tool not recognized i Installed Burning Tool with the driver
    have windows 7 64bit

    • MediaBox on January 8, 2017 at 4:36 pm

      New instructions check this 📣https://mediaboxent.com/unbrick-mxq-pro/

  5. Arcelio on December 26, 2016 at 10:59 pm

    saludos de Nuevo. el board dice esto mxq 905x 2q0160907 v2.0 creo que no realtek

    • MediaBox on January 1, 2017 at 10:06 pm

      tenes que mirar el chip del wifi, que le paso a tu caja?

  6. ron on January 1, 2017 at 2:19 pm

    It loaded to 94% then got temp out of range. Adjusted the temp range setting, now it keeps having romcode/initialize ddr/read initialize status/usb control setup error and the blue light does not come on any more. Any suggestions?

    • MediaBox on January 8, 2017 at 4:39 pm

      is possible that the box is running very hot

      • Ron on January 8, 2017 at 8:57 pm

        Thanks but could not get it to past 2% after that. Even leaving it for a while.

    • Keko Jones on February 7, 2018 at 12:36 am

      Hi there.
      In some ocasions there are a temperature error around 97% , its very simple to fix that problem just go to and click View and in the right side of the temperature parameters ad an extra cero (0) and should be ok to go 100% complete !
      Thanks For your videos and Firmware, ” Boricuas in the House “

  7. emiliano on February 26, 2017 at 9:20 am

    It asiking me to uninstall playstore updates because your box is not compactibile .

  8. emiliano on February 26, 2017 at 9:21 am

    i have ott mxq pro 4k

  9. Emiliano on February 27, 2017 at 5:29 am

    Hi can you help me please how to stop goole play store updating itself because when I try to enter on google play store app it gaves me this error .This version of the app isn’t compatible with your device.To fix this problem go to settings and uninstall updates for the google play store app.I followed all steps but still the same it updating itself from 5.1.1 version to 7.5 .I am waiting for your reply please.thanks

  10. Diederik on June 25, 2017 at 4:24 pm

    Hi, I have a ESP8089 chip, is there firmware for it. PLS.
    MXQ Pro 4K

  11. Jose opina on April 2, 2018 at 6:30 pm

    hago el procedimiento como lo indica el tutorial pero no corre ni con solo cable (tvbox a pc) no con el cargador del pc que puedo hacer

  12. Sosa on July 28, 2018 at 6:30 pm

    I have m9s pro if is a firware for it,the tv box crash how I fixed, any help pls.

Leave a Comment





This site uses Akismet to reduce spam. Learn how your comment data is processed.