Guiá Completa: Como instalar Raspberry Pi 3

Raspberry Pi 3 Tutorial: Raspbian Jessie Pixel instalación completa para principiantes.

En este video te enseñaré cómo instalar Raspbian a Raspberry Pi 3, lo haré sencillo y fácil incluso para aquellos que son nuevos en Raspberry Pi, te lo explicaré paso a paso, ya verás lo sencillo que es !

  • 1. Primero descargue el software y la imagen necesarios
  • 2. Instalar la imagen en la tarjeta SD
  • 3. Modifique el archivo config.txt para corregir sin problemas los vídeo para que no obtenga una pantalla borrosa al recibir.
  • 5. Ejecutar el raspi-config y hacer cambios 6. Actualizar el firmware.
  • 7. Actualizar el software
  • Divertirnos mucho

Tamaño de la tarjeta SD (capacidad). Para la instalación de NOOBS, el tamaño mínimo recomendado es de 8 GB.

Para las instalaciones de imagen recomendamos un mínimo de 4 GB. Algunas distribuciones, específicamente LibreELEC y Arch, pueden funcionar con tarjetas mucho más pequeñas.

Clase de tarjeta SD. La clase de tarjeta determina la velocidad de escritura sostenida para la tarjeta; Una tarjeta de clase 4 será capaz de escribir a 4MB / s, mientras que una clase 10 debe ser capaz de alcanzar 10 MB / s. Sin embargo, debe notarse que esto no significa que una tarjeta de clase 10 superará a una tarjeta de clase 4 para uso general, porque a menudo esta velocidad de escritura se logra a costa de la velocidad de lectura y de los tiempos de búsqueda aumentados.

 

 

raspberry_pi_model_b-1-800x657

Bajar los siguientes software.

  1. RASPBIAN JESSIE WITH PIXEL
  2. Win32 Disk Imager

Programas Recomendados

  1. SSH-Client
  2. Notepad-Plus
  3. VNC
  4. SD Formatter 4.0 for Windows

 

SD card size (capacity).

For installation of NOOBS, the minimum recommended card size is 8GB. For image installations we recommend a minimum of 4GB. some distributions, specifically LibreELEC and Arch, can run on much smaller cards.

SD card class.

The card class determines the sustained write speed for the card; a class 4 card will be able to write at 4MB/s, whereas a class 10 should be able to attain 10 MB/s. However, it should be noted that this does not mean a class 10 card will outperform a class 4 card for general usage, because often this write speed is achieved at the cost of read speed and increased seek times.

$ sudo raspi-config

Actualización  firmware
$ sudo rpi-update
$ sudo ldconfig
$ sudo shutdown -r now

Rpi-Actualizacion por primera ves:

$ sudo apt-get update
$ sudo apt-get dist-upgrade
$ sudo apt-get install -y rpi-chromium-mods
$ sudo apt-get install -y python-sense-emu python3-sense-emu
$ sudo apt-get install -y python-sense-emu-doc realvnc-vnc-viewer
$ sudo shutdown -r now

config.txt para monitor  HDMI reparar  gráficos borrosos

# For more options and information see
 # http://www.raspberrypi.org/documentation/configuration/config-txt.md
 # Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
 #hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
 # and your display can output without overscan
 disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
 # goes off screen, and negative if there is too much border
 #overscan_left=16
 #overscan_right=16
 #overscan_top=16
 #overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
 # overscan.
 framebuffer_width=1280
 framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
 #hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
 #hdmi_group=1
 #hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
 # DMT (computer monitor) modes
 #hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
 # no display
 #config_hdmi_boost=4

# uncomment for composite PAL
 #sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
 #arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
 #dtparam=i2c_arm=on
 #dtparam=i2s=on
 #dtparam=spi=on

# Uncomment this to enable the lirc-rpi module
 #dtoverlay=lirc-rpi

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
 dtparam=audio=on
 gpu_mem=256

 

HDMI A VGA MONITOR CON MONITOR HDMI A VGA

config.txt

# uncomment if you get no picture on HDMI for a default "safe" mode

hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible

# and your display can output without overscan

disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console

# goes off screen, and negative if there is too much border

#overscan_left=16

#overscan_right=16

#overscan_top=16

#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus

# overscan.

framebuffer_width=1024

framebuffer_height=768

# uncomment if hdmi display is not detected and composite is being output

hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)

hdmi_group=16

hdmi_mode=2

# overscan_scale=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in

# DMT (computer monitor) modes

hdmi_drive=2

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Subscribe to Media Box Entertainment Here: https://www.youtube.com/c/mediaboxent

Media Box Entertainment on Social Media:

Save

Save

Save

Save

 

Comments

comments

No comments yet.

Leave a Reply

Free Email Updates
We respect your privacy.
%d bloggers like this: